
Mr Ahmed Elsayed
Manufacturing Engineer
Advanced Forming Research Centre
Back to staff profile
Publications
- A Technical Presentation Summarising the Outcomes of Target Shape and Tooling Development
- Allazadeh Mohammad, Elsayed Ahmed
- (2025)
- AFRC-SRP02783-DIRF06477-D2
- Allazadeh Mohammad, Elsayed Ahmed
- (2024)
- AFRC-SRP02782-DIRF06477-D1
- Allazadeh Mohammad, Elsayed Ahmed
- (2024)
- An investigation on the potential of utilizing aluminum alloys in the production and storage of hydrogen gas
- Reda Reham, Ashraf Amir, Magdy Islam, Ragab Mohamed, Eldabaa Nada, Abo Elmagd Manar, Abdelhafiz Mohamed, El-Banna Osama, Fouad Amr, Aly Hayam A, Tlija Mehdi, Soliman Ahmed T, Elsayed Ahmed, Elshaghoul Yousef G Y
- Materials Vol 17 (2024)
- https://doi.org/10.3390/ma17164032
- Numerical analysis of the impact of winding angles on the mechanical performance of filament wound type 4 composite pressure vessels for compressed hydrogen gas storage
- Reda Reham, Khamis Mennatullah, Ragab Adham E, Elsayed Ahmed, Negm AM
- Heliyon Vol 10 (2024)
- https://doi.org/10.1016/j.heliyon.2024.e33796
- DIGF-PRS02623-DIRF06554-D1-Heating Trials Summary
- Jadhav Sandip, Elsayed Ahmed, Andreu Aurik
- (2024)
Back to staff profile
Projects
- AFRC-DIRF-07164
- ElRakayby, Hosam (Principal Investigator) Elsayed, Ahmed (Co-investigator)
- 06-Jan-2025 - 28-Jan-2025
- Finite Element Analysis of Hydroforming Process
- Elsayed, Ahmed (Principal Investigator) Allazadeh, Mohammad (Research Co-investigator)
- Finite element (FE) analysis was performed to investigate the feasibility of hydroforming a thick stainless-steel tray. The simulation results will provide information about the approach to form special thick stainless steel tray and the optimal design needed to form such thick component.
- 02-Jan-2024 - 12-Jan-2024
- Finite Element Analysis of Pressing Process of Thick Stainless Steel Tray
- Allazadeh, Mohammad (Research Co-investigator) Elsayed, Ahmed (Principal Investigator)
- Finite element FE analysis was performed to investigate the feasibility of pressing a thick stainless-steel tray. The simulation results will provide information about the approach to form particular stainless steel tray and the optimal design needed to form such thick component.
- 02-Jan-2024 - 12-Jan-2024
- DIGF-DIRF-06554_Experiment Design for the Heating of Metal Wind Turbine Bolt
- Jadhav, Sandip (Principal Investigator) Elsayed, Ahmed (Co-investigator) Andreu, Aurik (Co-investigator)
- 02-Jan-2023 - 29-Jan-2024
- DIRF_1948_ Al MMC sheets using Deep Drawing trails using cross shape geometry
- Jadhav, Sandip (Co-investigator) Elsayed, Ahmed (Co-investigator) ElRakayby, Hosam (Principal Investigator)
- 01-Jan-2021 - 27-Jan-2023
- AFRC-CRAD-1302 Carruthers Wheel: Very Low Head Hydro-Electricity
- Sancho, Alexander (Co-investigator) Parameswaran, Elangovan (Principal Investigator) Elsayed, Ahmed (Co-investigator) Marini, Daniele (Co-investigator)
- The design of a new waterwheel to be used for power generation in developing countries was developed. Computational Fluid Dynamics (CFD) models of the waterwheel were created and used to investigate its operating principle. The models were also used to validate experimental measurements taken from a prototype of the wheel. It was observed that the efficiency of the proposed system is significantly higher than that of more traditional designs.
- 18-Jan-2019 - 18-Jan-2020
Back to staff profile
Contact
Mr
Ahmed
Elsayed
Manufacturing Engineer
Advanced Forming Research Centre
Email: ahmed.elsayed@strath.ac.uk
Tel: 534 5657